Home Security Bundle Setup: Camera & Door Sensors
By iView US: iView | Affordable Laptops, Tablets, All-in-Ones ... | Published: 2026-10-20
Category: How-to Guides
Step-by-step guide to setting up your Panoramic Smart Camera and door sensors, including placement tips and common pitfalls to avoid.
Quick answer
This guide walks you through physically installing your panoramic camera and pairing the door sensors, so you can start monitoring entry points in under 30 minutes.
Choose the right location for each device
The panoramic camera needs a clear view of the area you want to monitor, but keep it away from direct sunlight and strong Wi-Fi interference sources like microwaves. Door sensors should be mounted on the door frame and the door itself, with the magnet aligned when the door is closed.
A common trade‑off: placing the camera too high for a wider view reduces the ability to see facial details. For indoor use, about 7–8 feet up works well.
Step‑by‑step setup process
- 1. Unbox and inspect components: Open the box and check that you have the panoramic camera, power adapter, mounting screws, the four door sensors, and the required batteries. Read the quick‑start guide for your specific model. Missing any part? Contact support before proceeding.
- 2. Mount the door sensors: Stick the larger piece (the sensor) on the door frame and the smaller piece (the magnet) on the door itself. Align the arrows on both pieces so they face each other when the door is closed. Clean the mounting surface first for strongest adhesion. Test the gap: the two pieces should be no more than 1 cm apart when the door is shut.
- 3. Pair the door sensors with the app: Open the companion app, go to the 'Add Device' section, and select 'Door Sensor'. Follow the on‑screen instructions to put the sensor into pairing mode (usually pressing a small button inside the battery compartment). If a sensor doesn't pair, remove and reinsert the battery, then try again.
- 4. Set up the panoramic camera: Place the camera in its intended location temporarily. Plug in the power, wait for the status light to blink amber, then open the app and add the camera. Connect it to your 2.4 GHz Wi‑Fi network using the app's QR code or WPS method. Common mistake: using a 5 GHz network or typing the Wi‑Fi password incorrectly. Verify the band and retype the password.
- 5. Position the camera and test the view: Once connected, adjust the camera angle in the app's live view. Use the pan and tilt controls to center the area you want to monitor. Tighten the base screw to lock the angle. Double‑check that the camera's view is not blocked by furniture or curtains.
- 6. Configure alerts and motion detection: In the app, enable push notifications for door sensor triggers and camera motion detection. Adjust the sensitivity of the camera's motion sensor to avoid false alarms from pets or passing cars. Start with a medium sensitivity and fine‑tune after a day of testing.
- 7. Secure the camera mount for permanent installation: When you are satisfied with the position, use the provided screws and anchors to mount the camera to the wall or ceiling. Route the power cable neatly and hide it with cable clips. Ensure no wires are pinched or exposed to water if mounted near windows.
What you'll be working with
- Home Security Bundle (CAM100 Panoramic Smart Camera × 1 and S100 Door Sensor × 4): The panoramic smart camera uses a 2MP CMOS sensor and captures 1920×1080 video at up to 25 fps. This means you get clear, smooth footage during the day, but low‑light performance depends on the built‑in IR LEDs (effective up to 10m).
Home Security Bundle (CAM100 Panoramic Smart Camera × 1 and S100 Door Sensor × 4) - Home Security Bundle (CAM100 Panoramic Smart Camera × 1 and S100 Door Sensor × 4): It only works with 2.4 GHz Wi‑Fi (IEEE 802.11b/g/n). If your router broadcasts both 2.4 GHz and 5 GHz networks, you must connect the camera to the 2.4 GHz band or disable the 5 GHz band temporarily during setup.
